When the Dyson DC40 vacuum cleaner starts making more noise and you notice that it does not seem to be cleaning as well, you may find yourself scratching your head and wondering what the next step should be.
This is where a Dyson DC40 Troubleshooting comes into play. It is a comprehensive guide on how to fix common issues with your Dyson DC40 vacuum cleaner in an easy-to-understand manner.
This troubleshooting guide will help you better understand the vacuum cleaner so that you can fix it by yourself or take it to get repaired professionally.
Troubleshooting the Problems of Dyson DC40 That Face Users
The Dyson DC40 comes with a 5-year warranty, making it one of the most popular models available on the market. But there are many problems that people face when they use a Dyson vacuum cleaner.
Some of these problems are not easily handled by the users, such as the defects in Dyson DC40’s motorized brush roll and its inability to turn off.
The following are some of the common issues faced by Dyson DC40 users:
No Suction from Hose
If you see that there is no suction that means the vacuum is not sucking any dirt or debris then it may be the problem of wrong height settings.
You have to set the accurate height of your vacuum compared to the floor and then try to run.
Brush Bar Not Spinning
Improperly assembled cleaning brush or damaged brush roll cannot spin properly and then it cannot clean any dirt too.
To avoid the problem, you have to look at three things- the brush roll spinning mechanism, the brush itself and the brush roll.
The brush roll can be damaged or scratched, the brush itself can be inappropriately assembled and the total brush roll mechanism cannot work due to the internal safety mechanism.
To clean the brush bar, use a soft cloth dipped in water or mild detergent with water as well as an old toothbrush to clean all parts of the brushes. Then use compressed air to blow out any remaining dust.
Overheating Problem
Overheating problem creates when the brush roll spinning system and not properly spin due to overloading to the spin wheel. It happens when long hair or any other clogs stuck with the brush roll. Except that, if the motor cannot load sufficient dirt, then overheating occurs.
There are multiple reasons why the DC40 overheats and cut out, but most often the issue is that the filter was not properly installed.
Cleaning clogs from the brush roll and spinning wheel is the first and easy way to prevent overheating. Then, you have to check the motor as because of low powered motor cannot go through huge dirt and thus, overheat produces.
A common issue with Dyson products is that they consume more power than similar brands of vacuum cleaners which can lead to overheating and cutting out.
However, this can be avoided by ensuring that the fan switch has been switched on before you start vacuuming, as well as checking to make sure it’s being powered by a plug rather than a corded cleaner.
Motor Not Working
Vacuuming mechanism runs on the spinning power created by the motor of any vacuum cleaner. If the motor cannot work properly due to low power voltage or damage power source then the mechanism does not run.
Check the damaged power source system that means the power cable and the battery if it is cordless one. Damaged battery cannot supply power to the unit and thus the motor does not work.
Blockages
Most common problems that people encounter with Dyson dc40 are related to blockages in the Swivel Base or filter bin. This can be solved easily by performing these troubleshooting steps:
-Turn off the machine and unplug it from its power source before proceeding.
-Remove Filters and Swivels from machine then extract all debris/clogs from machine’s filters & Swivels
–Clean filters after removing clogs
-Replace the filters if necessary
Basic Maintenance Tips for Dyson dc40 Vacuum Cleaner
Maintenance is a must for continuous operation of your vacuum cleaner. It is important to regularly clean the vacuum cleaner parts and service it when it requires repairs.
Here are some basic maintenance tips for the Dyson dc40 vacuum cleaner:
Clean the Filtration System
The Dyson vacuum comes with a filtered air wash system which includes two cyclones and two filters that help in trapping allergens and dust particles thus keeping your home cleaner.
Cleaning the filtration system can save you time and effort by sucking up almost anything on your floor without leaving piles or lumps behind.
It also doesn’t lose suction power over time or require special attachments for different surfaces as it comes with a tooling wand for hard floors and stairs.
Empty the Dirt Bin Regularly
To keep your machine functioning optimally, make sure that you empty out dirt and debris regularly using attachments like crevice tools, wands, or upholstery tool.
Dissemble the Detachable Parts and Dry Them
Dissembling the detachable parts after using the Dyson DC40, clean and dry them properly to reuse and this will help you play all the moving and others parts randomly.
Is There Any Reset Button on Dyson Dc40?
Actually, there is no reset button on Dyson DC40 vacuum cleaner. To reset it press the brush bar control button twice and turn it on again after switching off.
Why is my Dyson DC40 not picking up dirt?
The Dyson DC40 is an upright vacuum cleaner. It has a patented Radial Root Cyclone technology which separates the air in the tube. This makes the machine more efficient, and able to pick up more dirt at once. If your Dyson DC40 does not seem to be picking up any dirt, there may be something blocking it in the tube.
How do I know if my Dyson DC40 battery needs replacing?
The Dyson DC40 can be a powerful vacuum cleaner and it can clean your home in minutes. However, if you notice that the battery is dying faster than it should, it is possible that the battery needs replacing.
On the bottom of the vacuum cleaner there are three LED indicators. One indicator is for power, one indicator will indicate when a new filter needs to be put in and one indicator will indicate when it’s time for a change.
Do Dyson Vacuums have fuses?
In order to prevent the motor from overheating, Dyson vacuums still have a fuse. This fuse is a safety device that prevents the motor from being damaged by high electrical currents. Although these fuses are small and often hard to notice, they are there for your protection and will give you an early warning when something is wrong.
Conclusion
Dyson has a range of products that make our lives easier and more enjoyable like the DC40 Vacuum Cleaner, but it doesn’t always go smoothly.
When you will face problems like suction loss, blockage, overheating or motor not working then follow the basic troubleshooting methods we have discussed above that are designed to help users solve any problems that may arise with their Dyson DC40 vacuum cleaner.
If there are still issues, please contact their customer service team for further issues as Dyson has a team of professionals who can help troubleshoot your vacuum cleaner!
Leave a Reply